Showing results: 226 - 240 of 593 items found.
-
Dow-Key Microwave
MPG Switch line of High Power RF & Microwave Switches fit applications where electromechanical switches fail to meet the size, cost and speed of project specifications. At microwave frequencies, a high power switch acts as a current-controlled resistor, allowing current to flow in a single direction. When forward biased, the switch relay behaves as a closed circuit, but when the current is reverse biased, the RF switch becomes an open circuit.
-
Tabor Electronics Ltd.
The A10200 RF amplifier was designed to extend the power range of the Tabor arbitrary waveform generators and RF signal generators, yet it is compatible with many signal sources instruments.
-
96270A -
Fluke Calibration
The 96270A RF Reference Source is the simplest, most accurate and cost-effective single instrument for calibrating spectrum analyzers and RF power sensors and more, up to 27 GHz.
-
DVTest Inc.
USB 2.0 modules for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the USB 2.0 link untouched.
-
81060 -
Coaxial Dynamics
With the Model 81060 Directional Wattmeter you can now measure RF power in 50-Ohm coaxial cable and transmission lines without the need for additional plug-in elements.
-
81050 -
Coaxial Dynamics
With the Model 81050 Directional Wattmeter you can now measure RF power in 50-Ohm coaxial cable and transmission lines without the need for additional plug-in elements.
-
40-780A-574 -
Pickering Interfaces Ltd.
The 40-780A-574 is a quad SPDT 67GHz PXI microwave module and is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
OPT 80 -
Unaohm Start S.r.l.
Calibrated measurement of the optical power of satellite and terrestrial TV signals distributed in optical fiber Calculation of optical signal losses on distribution Measurement of digital parameters (BER - MER - NM etc.) of optical signals converted into RF Visualization of optical carriers in RF Field Metric Spectrum Analyzer Power Meter Optical Field Meter Display Optical RF Power Supply Line Link Meter (LNB power supply ) Optical LNB power supply 13V 500mA with short circuit and overload managementAcquisition of optical measurements using the field meter Data Logger Option: certification of the OPT80 calibration and optical power measurements
-
MRS-26D -
Hangzhou Huatai Optic Tech. Co., Ltd.
*Ultra low noise push-pull technology *Band width of 2.7 GHz* 46dB CNR (typ.) for NISC with OMI = 4% at –8dBm optical input power @ 1550nm* 20dBmV RF output level (-5dBm,1550nm,OMI=4%)* Very low intermodulations *Low power consumption *Small package with single-mode fiber pigtail *Integrated optical demultiplexer (WDM filer) for RF overlay applications *Monitor voltage output and output disable input
-
PGY-RFFE-EX-PD -
Prodigy Technovations Pvt. Ltd.
RFFE Protocol Analyzer (PGY-RFFE-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. The RF Front-end control interface (RFFE) Serial bus interface is emerging as a chosen for controlling RF frond end devices. There are variety of front end devices such as Power Amplifiers (PA), Low-Nose Amplifiers (LNA), filters, switches, power management modules, antenna tuners. It is widely used in mobile devices.
-
RF ITS -
Sterner Automation Limited
Sterner's automated test management system, combined with integrated RF technology modules, provides full functionality, including: Apply power to the device under test (DUT). Read and write blocks of data to set up and validate product EEPROM using a hard-wired communications interface. Scan transmitting devices or traveller barcodes and write the information to the DUT (the "sign-up process"). Inject an RF signal of known frequency and power level to test receiver sensitivity.
-
Insight Product Company
Pulsed injection locked amplifier incorporates IMPATT diode, ferrite input/output isolators, circulators, and pulse modulator. Only DC power supply, RF input signal, and external trigger signal are required to operate amplifier. Output phase noise parameters are very close to the noise parameters of the input RF signal.
-
Alfamation S.p.A
Infotainment systems have to deal with a several RF signals, starting from world radio standards but extending to mobile communication, GPS & WLAN. Most of the H.U. RF connections provide phantom power to active antennas that should be tested at different loading conditions (on more values, yet different case by case).
-
The Rotation Link SAS
The Swivel Joint is a special type of RF waveguide joint. It is a joint that is limited in rotation angle, compact in size, with low mechanical torque and high peak power capacity.
-
DVTest Inc.
SuperSpeed "USB 3.0 modules" for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the USB 3.0 link untouched.